Dana Gear Oil Synthetic 320 is based on synthetic hydrocarbons and a special plastic deformation (PD) and
Surface improvement additive package. The additive package, when activated by high specific loads and
Corresponding temperatures, helps to equalize surface roughness without creating abrasion leading to the
Surface improvement (plastic deformation.) gear oil synthetic 320 is a CLP-HC gear oil (according to DIN 51502)
And exceeds the minimum requirements according to DIN 51517, part 3, CPL gear oils.
Applications
Dana gear oil synthetic 320 may be used in spur gear, bevel gears or planetary gear units and in heavy loaded
Gear units. E.G. wind turbine main gears. It is also suitable for the lubrication of oil-lubricated rolling bearings.
Depending on the specific application, Dana gear synthetic 320 may be used in an operating temperature range
From 30 0c to + 90 oc.
BASIC BENEFITS
- High load carrying capacity.
- Superior micro pitting protection.
- Excellent friction reduction.
- Good filtration properties.
- Excellent bearing lubrication suitability.
Technical Product Data (TDS – DANA SYNTHEHTIC GEAR OIL ISO 320 MSD SYNTHETC GEAR OIL 320 NEW)
Download Technical Data Sheet ( TDS )
| Test | Method | units | X 150 | X 220 | X 320 | X 460 |
| ISO Viscosity grade | ASTM D 2422 | – | 150 | 220 | 320 | 460 |
|
Density at + 15 0C |
ISO 12185 / ASTM
D4052 |
g/ml |
0.847 |
0.85 |
0.854 |
0.856 |
| Kinematic viscosity
@ 400C @ 1000C |
ISO 3104 / ASTM D445 |
mm2/s mm2/s
|
146 19 |
218 25.9 |
325 34.9 |
459 45 |
| Viscosity index | ISO 2909 / ASTM 2270 | 148 | 151 | 152 | 153 | |
| Flash point, COC | ISO 2592 / ASTM D92 | 0C | >250 | |||
| Pour point | ISO 3016 / ASTM D97 | 0C | -39 | -33 | -33 | -27 |
| Rust test
Procedure A (24 hours Distilled water) Procedure B (24 hours synthetic sea water) |
ISO 7210 / ASTM D665 |
|
Pass Pass |
Pass Pass |
Pass Pass |
Pass Pass |
| Copper corrosion ( 3 hours @ 1000c | ISO 2160 / ASTM D130 | 1a | 1a | 1a | 1a | |
| FE8 Wear test (81212MPB-75/80-80)
Roller wear Cage wear |
DIN 51819-3 |
mg mg |
<10 <10 |
|||
| FZG test
A/8. 3/90 scoring load stage A/16. 6/90 scoring load stage |
DIN 51354 |
>12 12 |
||||
| FZG micro pitting test | FVA NO.54 | >10 | ||||
| Foam sequence l | ISO 6247 / ASTM D892 | ml | <100/10 | |||
| Ageing behavior, increase of viscosity at
1000c after 1000 h |
ASTM 2893 |
% |
2 |
|||
Subject to usual manufacturing tolerances.
Additional information
Dana synthetic 320 gear oil can be applied by an oil can, oil cup reservoir, Splash , spray mist or by automatic
Dispensing equipment and central or circulation systems. It is compatible with mineral oil and esters. This means that
traces up 3% of previous oil in the gear case after draining will not pose any problems. However, the beneficial
effects of the special PD additive are reduced when mixed with other gear oils.
About manufacturer
Dana Lubricants Factory, Dubai based , Petrochemical manufacturer and supplier for wide range of Petrochemicals covering Base oils, Solvent Neutral Sn 100/150/300/500/600/900 , Automotive Lubricants and engine oils , Industrial Lubricant Oils and Grease , White oils and Petroleum Jelly, Octane Booster and Fuel Additives , Transformer oils Paraffinic and Napthenic , White spirit , Mix Xylene toluene and Rpo . Middle east is hub for all petrochemicals refined, produced and packaged in UAE in bulk packing like Iso , Flexi , Drums ( Metal drums and plastic drums ) , Ibc ( tote) and exported to across the globe using standard 20 ” and 40″ containers.
Dana Petrochemicals , Dana Plastics , Dana Lubricants , Dana Base oils , Dana Transformer Oils , Dana Paints , Dana Steel are all different divisions of Dana Group of Companies spread around in entire UAE covering all emirates Dubai , Abu Dhabi , Ajman, UAQ and other countries like India, Saudi Arabia and Oman .
For more details , visit http:// www.danalubes.com , http://www.danagroups.com
Download Technical Data Sheet ( TDS )
